Search results

I am selling my Sport Trac. It is a 2002, Black, with all options. 140k miles. A coil over conversion was completed in 2005. Fits 33x12.50 on 15x10 wheels with a deep offset. The rear 60,40 bench seat has been modified to accommodate a center consul/speaker box. A screen is mounted on the...

I need the black plastic trim only from the Ignition Lock Cylinder repair kit. I am trying to avoid having to buy the whole switch repair kit. My trim piece sheared off at two of the retaining clips and fell off :(

Would you happen to have the center console storage box like the one pictured here? I need one.

I ended up purchasing new passenger Axle Shafts from Ford. Turned out that the axle shafts purchased from Oriellys didn't have an added collar for the rubber seal to nest into.

Does anyone have: Rear, Right Hand Quarter Panel Inner Wheel Housing Rear Bumper Cover (No Gouges or Scratches) Rear Bumper Step Pads (Not Faded)

Do You have: Rear, Right Hand Quarter Panel Right Hand Inner Wheel Housing (circled in red is the left as an example) Rear Bumper Cover Rear Bumper Step Pads

Seems to be slow enough to just leave alone. I will degrease the area. Sounds like a fun clean up job.

I mentioned earlier that the passenger CV Axle and shaft were able to shift laterally about a 1/4" of an inch. I made a quick video for you to look at. Password: zxcvbn Is it supposed to do that? When the shafts are in the outer most position away from the center of the vehicle oil will...

There is a lot of oil residue on the front of the upper oil pan. What is leaking? When checking my oil after 4,000 miles, the levels are perfect. Could it be leaking just behind the under drive pulley? Is this common for a 2002 with 87,800 miles? Pictures are taken of engine front...

So, concerning the axle shaft and inboard CV on the passenger side, expect the axle shaft to come sliding out of the axle housing. Disconnect the inboard CV by wedging a tool between the axle and the inboard CV and the come apart just fine. When sliding the axle shaft in and out to do work...

I am so happy to see this posting even though it is about a challenge that is not yet solved. I was replacing my CV joints on the right side a couple of weeks ago as well. -I was able to separate the existing inboard CV from the axle shaft with my own pulling force. -I did not know...

I am experiencing the issue of leaking fluid at the end of the axle shaft housing after replacing the CV joints on the passenger side. However, I am wondering if something is unique: the axle moves about 1/4 of an inch lateral. When it is closest to the center of the truck, no visible fluid is...

I just did my front wheel bearings and the project was not too bad. The biggest challenge was getting the right angle and torque to take out the bolts for the hub assembly. The factory LockTight makes it hard. Then, once the bolts are out, some creative prying and tapping with a hammer gets...

If you can provide an STL (STereoLithography) file after modeling the piece in sketch up, then you can have it printed yourself with some high grade plastics here: http://www.stratasys.com/

I found CV Grease thrown around on my passenger front wheel, outer joint yesterday after hearing some clicking/rattle when going over small bumps on the road. I drove a few blocks to get back to the driveway and found the grease. Due to the low amount of time driven and only hearing the...

Bummer! I will make sure there is enough grease then.

Thank you for your thoughts Chad. The Shaft is new. Do you think it would still need a grease check?

I installed the Super Lift Drive Shaft (Prt#9636) yesterday. I took photos and recorded the tools needed to post the info here. Has anyone noticed the double cardan joint humming at speeds of 45 and above? The stock drive shaft was beginning to make a faint noise at higher speeds due to the...

No pictures yet?

Can you send me a picture showing the condition of the CV boot? Thankyou