Search results

While driving on the freeway over the weekend my temp gauge would periodically jump up to high and the check gauge light would come on for about 3-4 seconds and then return to normal for about 5 minutes. Other than the gauge moving, the truck seem to run the same and there was no noticeable...

I have a 2003 4x2 with a spindle/leaf spring lift with 33" tires. I have had my wheels rotated/ balanced and also have had a front end alignment after replacing the camber washers. I still have a vibration when traveling between 60-70 mph. Any suggestions? I read the previous posts about...

Does anyone have a set (or even just one) headlight that they no longer need? Thanks.:D

Items for sale: 1) Set of 4 Goodyear Wrangler RT/S P255/70R16 with approx. 1/4in tread. 2) 2003 Stock Rims 3) Ram Side Trax step bars, black, for 2003 Sport trac, Have almost all hardware, only missing retaining clips. I am trying to sell locally(located in lubbock, tx) so that...

Teddy -- you got mail.

I am looking to buy a set of 2003 stock headlights! Anyone got some laying around? Thanks

I am retrofitting some bixenon projector headlights into my trac. I have a new harness to preplace the stock 9007 harness. Anyone know where the harness plug is located? I think that it is located somewhere on the driver side but need more specific location. Thanks in advance. MCbrainz

I am looking to aquire some clear corners for my 2003 trac. anyone got some laying around that they would like to part with? Thanks.:D

Does anyone know offhand the dimensions for the stock headlight housing for the 2003 trac? I am planning on doing a HID retrofit and need to make sure i will have enough clearance for the projectors. thanks.

I am planning to retrofit HID projectors into the stock housing and fit them with angel eyes, also clear corners with LEDs, and finally I have taken off my nerf bars and I am replacing them with the individual steps at each door. :D

I am trying to decide whether I should go with a tonnaeu cover or bed cap. Can some of you guys show some pics so I can get a feel for the various looks. Thanks in advance. Mcbrainz

Just installed the fabtech lift spindles, now i have experienced a strange brake problem. Whenever I turn sharply to the left or go over a curb, my brake pedal will go to the floor for the next pump of the brakes, and then the next pump will react normally. Luckily i havent had to stop...

Dave S. I sent you an email concerning the spacers. Mcbrainz

Dave S. Are those spacers you have the billet type? If so, I am interested in aquiring them. MCBrainz

I just installed the fabtech lift spindles and now my front tires stick out past the fender. I would like to make the rear wheels match. Anyone reccomend somewhere to order some wheel spacers? and what is the max spacing while still being safe? pics of new installed parts to follow after...

thanks clay, any problems thus far that you have experienced with the setup? How about the ABS sensors, do they reinstall nicely? Were you able to get your old spindles off your ball joints or did you replace them? If you replaced them, how hard was it to get the ball joints pressed back...

I am installing my fabtech lift spindles today and I have a few questions. First, i know the instructions are for a 2001 Ranger Edge, so how closely do i have to follow the modification steps? for example, do i have to cut off the steering block from the lower control arm, and also, do i have...

Finally got the time this weekend to install my lift spindles and new rear leaf springs with my new wheels and tires!! I was reading the instructions for the fabtech spindle install, and it was mentioning using a grinder to modify the upper control arm?? Is this necessary for the Trac or were...

Yes, they are always on. I had the same question when i did mine. I think i never noticed before because the Green light was not strong enough to be seen all the time as is the more bright blue led.

Anyone here know any insider information on when fabtech will start shipping their spindles again? I ordered some spindles at the end of july and have yet to recieve them. I spoke to several truck shops and they all say the hold up is at fabtech. Cant wait to lift my trac!