Search results

Yeah Todd, any news? I'm having the exact same problem, and it's driving me crazy...

Alright....so I finally got my jackstands back. I'm going to rebleed the entire system, including the master cylinder. One question though....do I bleed the master cylinder first, or do I bleed it last?

Well it's definately not the booster. Next step is to wait for a buddy to return my jackstands:angry: then I will rebleed the whole system (master cylinder too this time) old school style...pump the brakes..open the bleeder etc etc. I will try bleeding it with the engine running this time to see...

Have you tried adjusting the idle speed? I had a problem 2 winters ago, when stopped at a light with the heat running the truck would surge and then try and die. It ended up being that when you have the heat on or (AC in this weather), the AC compresser kicks on and if your idle speed is just a...

After some further research...To test if the brake booster is performing- With the engine off depress the brake pedal several times to remove residual vacuum in the booster. Pedal should be high and firm. With your foot on the brake pedal, start the engine. The brake pedal should then depress...

Thanks for the input guys. I'll check the "check valve" on the booster this weekend. As far as back flushing old fluid into the abs, I did remove the bleeders before pushing the pistons back. When finished I power bled the entire system until new fluid came out of each bleeder. Keep the...

Back story: Replaced rear shoes, front pads and rotors, installed speed bleeders, and then power bled the system. Problem: Pedal is firm and high with engine off. However, during driving conditions sometimes the pedal is high (where it should be after bleeding) and sometimes the pedal...

Can anyone tell me how many of each bulb (194 and 37) I'll need to replace the bulbs within the gauge cluster. I've read both member projects on the subject, but neither tells how many bulbs are required. I figured if I have to replace one bulb, I'd might as well do them all when I have the...

At the time I made it I had access to a stereo lithography machine (SLA). At my present job, I don't have direct access to one. I can look into it and get a quote, but I don't think it will be cheap by any means....

Here's mine. I used an AUX-POD integration set up. It allows you to have basic controls thru the stock head unit and charges the Ipod at the same time. I also fabrication a Ipod Cup Holder.......Yes, I know the pict is huge.[Broken External Image]:

Charlie...25lb Pug...all attitude![Broken External Image]:

Scott, here is a link as to where you can purchase the unit...they also carry the cable you will need Jeff C....this unit charges the ipod as well. Just a thought

I have the same radio. Below is the link to what I used. I've had it approx 4 years now with no problems. The AB-FRD20 cable piggy backs inbetween the cable that leads to the rear seat controls. Once hooked up, just press the "CD" button a second time to switch to it. The sound is great and you...

Here are some quick photoshop color options...[Broken External Image]:[Broken External Image]:[Broken External Image]:

I had a similar experience with mine, and it ended up that my idle speed was set too low. When the idle speed of the engine is too slow the compressor will not stay on, it will cycle on and off. The compressor cycles on, senses that there is not enough speed to maintain compression, and then...

Good call. If you can stay digital (HDMI to DVI) that is definately the way to go. I should have read the post in a little more detail. Good luck!

I believe that this might be what you are looking for. I've purchased from them before, and have been very satisfied. This cable comes in 6', 12', 25' and 50' lengths. Hope this helps

I too have the rattling passenger seat. After driving me insane for the past year with no obvious solution to the problem, I decided to tackle it. I've found that while I connot stop the vibration of the seat, I've found the rattle and remedied it. The rattle comes from a spring that is attached...

Still needed and much appreciated! Thanks a lot!!!!!!

Hi Everyone, I just purchased 2 new front hub assemblies for my 01 4x4 Trac. Does anyone know the torque specifications for attaching the hub assembly to the steering knuckle? Do I need to use loctite, and if so, what type? Any help would be greatly appreciated. Thanks,