Search results

Ford SportTrac Forum

Help Support Ford SportTrac Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. J

    Wanted factory hard tonneau Gen2 hardware and lock covers

    Thanks Todd I was hoping i could find used and save a few bucks. Jim
  2. J

    Wanted factory hard tonneau Gen2 hardware and lock covers

    Need the strikers and lock covers for a GEN 2 factory hard folding cover.
  3. J

    Tonneau cover width

    Can someone tell me the width of a gen1 cover compared to a gen 2? I have a guy that has one he claims is a gen2 because it is too narrow to fit his gen1 would this be correct. Thanks Jim :supercool:
  4. J

    THrottle position sensor

    You were right about the wiring it is brittle right were it comes out Of the connector I took some Liguid tape and coated them if that makes a difference I'll wire in a new connector. Thanks Jim
  5. J

    Tonneau cover gen 1 & gen 2

    Thanks in my area I've came across two gen 1 But no gen 2, I'll keep looking. Thanks Jim
  6. J

    Tonneau cover gen 1 & gen 2

    Has anyone tried putting a gen 1 on a gen 2? Is there that much difference in the beds? This is my first ST but I'm loving it. Jim
  7. J

    THrottle position sensor

    On a Gen 2 do you need to pull the throttle body to change the sensor? I know it Is on the back and could be a little challenging but is better to pull the throttle body. Thanks Jim
  8. J

    ck eng light and wrench help

    I have a 2008 ST 4.0 got the two lights today as I was getting on the highway and you could tell it wasn't running right but it did get up to speed but once into overdrive it would surge and it would not let you set the cruise. Turned around and took it home pulled codes and got P0401, P2135...
  9. J

    need help

    I forgot to say it is 4.0 91000 miles.
  10. J

    need help

    :cry:I cant get anyone's help with my other post maybe this one. can someone tell me where the DPFE sensor is on a 2008 Sport Trac, I bought this one about 2 months ago and I got the famous P0401 code and I can tell it has a brand new EGR valve installed so it has got to be the DPFE I would...
  11. J

    EGR insufficient air flow

    Got the EGR code on a 2008 with 91000 miles 4.0 v6 I can clear the code and it will come back after a couple of days what should I change first or look at. Thanks for any help.:banana:
  12. J

    TONNEAU COVER

    Will a GEN1 Tonneau cover fit a GEN2?
  13. J

    Died in car wash 2008 ST

    Thanks for all the help and my get up has gone to!!:driving:
  14. J

    Died in car wash 2008 ST

    where is the fuel pump driver module located?
  15. J

    Died in car wash 2008 ST

    Today I'm sitting in the car wash and right before it finished it died, and wouldn't restart. I got a guy to help me push it out. tried restarting all the dash lights come on but no crank, then on about the third try it cranked tried to start but sounded like it was misfiring then died did this...
  16. J

    Jack handle

    I don't need the one with the hook on it I need to seethe one that goes down in the tube. Jim
  17. J

    Jack handle

    I don't need the one with the hook on it I need to seethe one that goes down in the tube. Jim
  18. J

    Jack handle

    Thanks for the replays but I need to see what the end looks like that goes in below the bumber, having owned fords before I know they have changed over the years we tried using a friends 2004 ranger handle and it wouldn't work. I own a 2002 Ford F-150 and it has a special socket that goes on the...
  19. J

    Jack handle

    I just bought a 2008 sport trac and didn't relize it didn't have a jack or handle s:supercool:o I have no way of getting the spare down can someone show me a picture of what the end of the handle looks like that will lower the spare, that way if I go to a junk yard I'll know what I'm looking...
Top